2022 Updated NS0-184 PDF for the NS0-184 Tests Free Updated Today!
Fully Updated Dumps PDF - Latest NS0-184 Exam Questions and Answers
NetApp NS0-184 Exam Topics:
| Section | Objectives |
|---|---|
| ONTAP Networking | - Describe how to configure ONTAP system networking - Describe network types used with ONTAP clusters |
| ONTAP Configuration | - Describe how to add or remove nodes in an ONTAP cluster - Describe how to set up cluster peering - Describe how to implement security hardening - Describe support resources required for troubleshooting ONTAP installations |
| ONTAP Switches | - Describe cabling of a switched cluster - Identify the software needed for cluster switch configuration |
| Basic Installation Topics and Tools | - Describe the required tools or documentation for preparing the installation of a new ONTAP cluster -Describe physical cabling of ONTAP nodes |
| Customer Handoff | - Describe the tools available to review an installation - Describe the process for handover of new ONTAP cluster installation to the customer - Identify how to create documentation |
NEW QUESTION 17
Click the Exhibit button.
You want to add an AFF A400 system to an existing 4-node cluster.
Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 18
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. SNMP traps
- B. EMS messages
- C. command history
- D. AutoSupport messages
Answer: C,D
NEW QUESTION 19
Click the Exhibit button.
You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.
Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)
- A. larger than PMTU communication succeeds on 4 path(s)
- B. 2 paths up, 0 paths down (UDP check)
- C. 2 paths up, 0 paths down (TCP check)
- D. basic connectivity succeeds on 4 path(s)
Answer: C,D
NEW QUESTION 20
You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.
In this scenario, which front-end FAS8300 network port would you create the data LIFs?
- A. e0e-100
- B. a0a-100
- C. a0a
- D. e0e
Answer: D
NEW QUESTION 21
Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.
Which two actions would enable the customer to accomplish this task? (Choose two.)
- A. Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.
- B. Deploy new, dedicated, storage switches for the new NS224 shelves.
- C. Deploy a new AFF A400 to the cluster.
- D. Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.
Answer: C,D
NEW QUESTION 22
You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.
In this scenario, which two flow control settings would you verify? (Choose two.)
- A. Verify that the data network ports have full flow control disabled.
- B. Verify that the data network ports have full flow control enabled.
- C. Verify that the cluster network ports have full flow control disabled.
- D. Verify that the cluster network ports have full flow control enabled.
Answer: A,D
NEW QUESTION 23
You installed two separate clusters in an isolated data center without outbound network access. The customer wants to troubleshoot issues locally and also create custom Excel reports for capacity utilization from a local server.
In this scenario, which NetApp tool would satisfy this requirement?
- A. Cloud Insights
- B. Active IQ Unified Manager
- C. Active IQ Digital Advisor
- D. ONTAP System Manager
Answer: B
NEW QUESTION 24
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?
- A. FTP
- B. HTTP
- C. HTTPS
- D. SMTP
Answer: C
NEW QUESTION 25
In an ONTAP 9.7 cluster, which LIF role is used for sending AutoSupport, establishing Network Time Protocol (NTP), and loading software updates?
- A. cluster LIF
- B. data LIF
- C. cluster management LIF
- D. node management LIF
Answer: D
NEW QUESTION 26
You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.
In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)
- A. Cable the AFF A250 nodes to the next free ports on the switch.
- B. Load the Cluster-HA-Breakout RCF.
- C. Cable the AFF A250 nodes to the breakout ports on the switch.
- D. Load the Storage RCF.
Answer: B,C
NEW QUESTION 27
Click the Exhibit button.
You are installing a new AFF All SAN Array A700 HA pair.
Referring to the exhibit, which IP address would have been used to join node 02 to the cluster during setup?
- A. 192.168.0.112
- B. 169.254.212.198
- C. 192.168.0.101
- D. 169.254.145.151
Answer: A
NEW QUESTION 28
You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither "un-failing" nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.
In this scenario, which two actions should you take? (Choose two.)
- A. Ask the customer to open a technical case with NetApp Support.
- B. Run Active IQ Config Advisor to collect all the logs on the system.
- C. Power off the system until the drive has been replaced.
- D. Ask the customer for a drive with the same capacity and replace it.
Answer: B,D
NEW QUESTION 29
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. intracluster SnapMirror
- B. cluster database replication
- C. intercluster SnapMirror
- D. remote cluster peering
- E. Epsilon voting
Answer: B,C,D
NEW QUESTION 30
You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.
How do you verify your configuration?
- A. Use the disk show -fields initiator command.
- B. Use the sysconfig command.
- C. Use the storage disk option show command.
- D. Use the storage show disk -p command.
Answer: A
NEW QUESTION 31
What should you do to change the data protocol of a LIF?
- A. Add the new data protocol to the LIF.
- B. Put the LIF in another broadcast domain.
- C. Shut down the assigned port.
- D. Delete and re-recreate the LIF.
Answer: D
NEW QUESTION 32
You want to add an AFF A400 HA pair to an existing cluster.
In this scenario, which LIF type is required?
- A. cluster-mgmt
- B. intercluster
- C. node-mgmt
- D. data
Answer: B
NEW QUESTION 33
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?
- A. IPspaces
- B. BGP
- C. broadcast domains
- D. routing
Answer: C
NEW QUESTION 34
You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.
In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)
- A. port sets
- B. switch zoning
- C. failover groups
- D. reporting nodes
Answer: A,C
NEW QUESTION 35
You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.
Which two additional steps must be taken to bring the additional ports online? (Choose two.)
- A. Reload the firmware
- B. Reload the RCF file
- C. Reload the switch
- D. Re-enable each port
Answer: B,C
NEW QUESTION 36
You installed a new pair of Cisco 92300YC cluster switches at a customer's site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?
- A. switchcfgshow
- B. fabricshow
- C. config show
- D. show running-config
Answer: A
NEW QUESTION 37
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)
- A. Active IQ Unified Manager
- B. Hardware Universe (HWU)
- C. AFF FAS Documentation Center
- D. hardware installation setup poster
- E. Interoperability Matrix Tool (IMT)
Answer: B,C,D
NEW QUESTION 38
......
Free NS0-184 Exam Questions NS0-184 Actual Free Exam Questions: https://www.testsimulate.com/NS0-184-study-materials.html
100% Free NS0-184 Exam Dumps to Pass Exam Easily: https://drive.google.com/open?id=1eNlRGdIEBXbvINcovhcaAwqr3F2gNtiD