Riverbed Certified Solutions Professional (199-01) Free Practice Test

Question 1

When using Correct Addressing and enhanced auto-discovery (EAD), what is the size of the probe response in the return SYN/ACK packet from the server?

A. 18 bytes

B. 14 bytes

C. 10 bytes

D. 32 bytes

E. 4 bytes

Correct Answer: A

Question 2

To configure a Steelhead appliance for logical in-path mode, the following must be enabled in the General Service Settings page:

A. Reset Existing Client Connections on Start Up

B. B and C

C. A, B, and C

D. Enable Optimizations on Interface inpath0_0

E. Enable L4/PBR/WCCP Support on Interface wan0_0

Correct Answer: B

Question 3

Assuming auto-discovery is used, WCCP redirect-in statements would normally be placed on which router interfaces? (Select 2)

A. The interface that the Steelhead appliances are connected to

B. The interface on the WAN side

C. The interface on the LAN side

D. The loopback interface

Correct Answer: B,C

Question 4

The adaptive data streamlining settings are:

A. Default , RiOS SDR- L, RiOS SDR-M

B. Default , RiOS SDR- Adaptive, RiOS SDR-M

C. Default , RiOS SDR- Adaptive, RiOS SDR-L

D. RiOS SDR- Adaptive, RiOS SDR-L, RiOS DSR-M

E. Default , RiOS DSR- Adaptive, RiOS DSR-M

Correct Answer: B

Question 5

You need to take a full packet trace from the WAN interface of a Steelhead appliance to send into technical support.Which of the following commands will achieve this assuming typical Ethernet MTU? (Select 2)

A. tcpdump -i wan0_0 -w filename

B. tcpdump -i wan0_0 -s 0 -w filename

C. tcpdump -I wan0_0 -s 1500 -w filename

D. tcpdump -I wan0_0 -w filename

E. tcpdump -i wan0_0 -s 1500 -w filename

Correct Answer: B,E

Question 6

What are the possible ways to downgrade a Virtual Steelhead appliance after it has been upgraded?

A. Reduce the amount of CPU and RAM allocated to the Virtual Steelhead appliance and it will automatically downgrade at the next startup

B. Reinstall the original model license

C. It is not possible to downgrade after an upgrade

D. Remove the upgrade license and restart the virtual Steelhead appliance

Correct Answer: C

Question 7

In configuring failover settings, which of the following ports is set as the default for communicating with the backup Steelhead appliance?

A. 7766

B. 7820

C. 7600

D. 7744

E. 7850

Correct Answer: B

Question 8

-- Exhibit-

-- Exhibit -
Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Intercetor appliances, and the Steelhead appliance, he decided to check if the devices will work appropriately. Which Intercetor appliance diagnostic tool did the administrator use?

A. The command "connection tracing".

B. The command "debug validate deployment".

C. The command "debug tracing".

D. The command "debug deployment validation".

Correct Answer: B

Question 9

You are using Steelhead appliances in an Oracle Forms environment and are not seeing adequate acceleration.What could be the cause of this?

A. Oracle Forms optimization only works with Oracle Applications 9i

B. Oracle Forms optimization only works with Oracle Applications 8i

C. You need to install a separate Oracle Forms license

D. Oracle Forms optimization can only be configured from the command line (CLI)

E. Oracle Forms optimization is enabled by default. However, you must set an in-path rule to enable this feature.

Correct Answer: E

Welcome to TestSimulate

Riverbed Certified Solutions Professional (199-01) Free Practice Test