Pure Storage Certified FlashArray Implementation Specialist (FlashArray-Implementation-Specialist) Free Practice Test

Question 1

An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray. After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

A. find_drive.py

B. puredb list drives

C. puredrive list --pack CH0.BAY10

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 2

A customer has ordered several FlashArrays and wants to have ActiveCluster configured. What is the maximum quantity of arrays supported with ActiveCluster?

A. 4

B. 3

C. 2

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 3

Which PCI cards must be validated on the Bill of Materials (BOM) to allow an Implementation Engineer to attach a DirectFlash Shelf to a FlashArray//XL130R5?

A. FA-XL-100G Ethernet/RoCE 2-Port

B. FA-XL-200G Ethernet/RoCE 2-Port

C. FA-XL-100G iSCSI/RoCE 2-Port

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 4

During a hardware NDU from a FlashArray//X20R3 to an X20R4-LL (low-line) model, the Implementation Engineer encounters a failure during the power supply check. Voltage readings are correct.
What is a likely cause of this failure?

A. The facility power is providing 208V instead of 120V.

B. The power cables are NOT fully seated in the array.

C. There are more than 10 drives installed in the chassis.

D. Purity does NOT recognize the power supplies installed in the array.

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 5

What are the default replication ports on all three rack unit FlashArray models?

A. ETH2 and ETH3

B. ETH4 and ETH5

C. ETH0 and ETH1

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 6

Refer to the exhibit.
During the puresetup portion of the new controller setup of an NDU, the Implementation Engineer gets an error message regarding missing or unassigned network interfaces.
What action should the Implementation Engineer take next?

A. Continue with the setup process and manually add the affected ports once it is complete.

B. Identify which services will be affected, stop the process, and open a case with a TSE before moving forward.

C. Identify which services will be affected, and then re-run the puresetup command with the affected ports included.

D. Re-seat the network cables and reboot the controller to clear the error.

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 7

The customer has completed the installation document and has stated that the proxy server address is
"10.24.18.120". What additional information is required?

A. Protocol prefix and port number

B. Credentials and port number

C. Protocol prefix and credentials

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 8

What is the minimum supported capacity requirement for a FlashArray//XL170R5?

A. 115TB

B. 182TB

C. 135TB

D. 90TB

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 9

Which PCIe slot must be used for a SAS HBA on R4B revision controllers?

A. PCIe slot 4

B. PCIe slot 0

C. PCIe slot 1

D. PCIe slot 2

Correct Answer: B

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 10

Which user does an Implementation Engineer use when preparing for the Purity upgrade to complete a HWNDU?

A. pureuser

B. puresetup

C. pureinstall

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 11

After racking a new FlashArray with one data pack, how should DirectFlash modules be installed?

A. Starting in bay 10, left to right.

B. Starting in bay 0, left to right.

C. Starting in bay 19, right to left.

Correct Answer: B

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 12

What upgrade scenario required an upgrade of power supplies?

A. X50 > X70

B. X10 > X50

C. X50R2 > X50R3

Correct Answer: B

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Welcome to TestSimulate

Pure Storage Certified FlashArray Implementation Specialist (FlashArray-Implementation-Specialist) Free Practice Test