Enterprise Routing and Switching, Specialist (JNCIS-ENT) (JN0-352) Free Practice Test

Question 1

Which statement is correct about the configuration shown in the exhibit?

A. The configuration will not complete the commit check process and will error out.

B. The ge-0/0/2 interface is operating as a Layer 3 interface.

C. The ge-0/0/0 and ge-0/0/1 interfaces are operating in trunk mode.

D. All three interfaces are operating in access mode.

Correct Answer: D

Question 2

Which command solves the error that you see in the exhibit?

A. set ge-0/0/2 unit 0 family ethernet-switching vlan members [default v11]

B. delete ge-0/0/2 unit 0 family ethernet-switching vlan members all

C. delete ge-0/0/2 unit 0 family ethernet-switching vlan members default

D. set ge-0/0/2 unit 0 family ethernet-switching vlan members all

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 3

Your ISP is announcing a default route to both R1 and R2. You want your network routers to forward all Internet traffic through the R1 device.
Which BGP attribute would you use?

A. MED

B. next-hop

C. local preference

D. origin

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 4

Which two statements correctly describe RSTP port roles? (Choose two.)

A. The root port is responsible for forwarding data to the root bridge.

B. The backup port is used as a backup for the root port.

C. The alternate port is a standby port for an edge port.

D. The designated port forwards data to the downstream network segment or device.

Correct Answer: A,D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 5

You implemented the MAC address limit feature with the shutdown action on all interfaces on your switch.
In this scenario, which statement is correct when a violation occurs?

A. By default, devices that are learned before the violation occurs are still allowed to send and receive traffic through the specific interface.

B. By default, the interface will continue to send and receive traffic for all connected devices after a violation has occurred.

C. By default, the violation will automatically be cleared after 300 seconds and the interface will resume sending and receiving traffic for all learned devices.

D. By default, you must manually clear the violation for the interface to send and receive traffic again.

Correct Answer: D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 6

Which statement is correct about graceful Routing Engine switchover (GRES)?

A. The PFE restarts and the kernel and interface information is lost.

B. GRES has a helper mode and a restarting mode.

C. With no other high availability features enabled, routing is preserved and the new master RE does not restart rpd.

D. When combined with NSR, routing is preserved and the new master RE does not restart rpd.

Correct Answer: D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 7

Which statement is correct about the storm control feature?

A. The storm control feature is not supported on aggregate Ethernet interfaces.

B. The storm control configuration only applies to traffic being sent between the forwarding and control plane.

C. The storm control feature is enabled in the factory-default configuration on EX Series switches.

D. The storm control feature requires a special license on EX Series switches.

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 8

Which statement is correct about the exhibit?

A. All routes from inet.0 will be imported into first.inet.0 and second.inet.0.

B. Only the interface routes from inet.0 will be imported into both first.inet.0 and second.inet.0.

C. All the routes from first.inet.0 and second.inet.0 will be imported into inet.0.

D. Only the interface routes from first.inet.0 and second.inet.0 will be imported into inet.0.

Correct Answer: B

Question 9

The ISP1.inet.0 route table has currently no routes in it.
What will happen when you commit the configuration shown on the exhibit?

A. The ISP1.inet.0 route table will be imported into the inet.0 route table.

B. The inet.0 route table will be imported into the ISP1.inet.0 route table.

C. The inet.0 route table will be completely overwritten by the ISP1.inet.0 route table.

D. The ISP1.inet.0 route table will be completely overwritten by the inet.0 route table.

Correct Answer: B

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 10

Which two statements are correct about generated routes? (Choose two.)

A. Generated routes require a contributing route.

B. Generated routes appear in the routing table as static routes

C. Generated routes cannot be redistributed into dynamic routing protocols.

D. Generated routes show a next hop in the routing table.

Correct Answer: A,D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Welcome to TestSimulate

Juniper Enterprise Routing and Switching, Specialist (JNCIS-ENT) (JN0-352) Free Practice Test