Cisco Deploying Cisco Wireless Enterprise Networks (300-365) Free Practice Test
Question 1
A customer has implemented a wireless network that requires tuning for High Density applications utilizing the RX-SOP feature. They are experiencing a high noise floor (average of -65 dBm) and expect that to decrease significantly. A sampling of radios determine that most Access Points have neighbors on the same channel at a power level of -75 dBm. Which value should the customer use to start tuning RX-SOP?
Correct Answer: B
Question 2
Scenario:
You have been tasked with setting up a mobility group (Mobility_Test) in a test lab. Thereare two WLCs that you will need to configure (Test1 and Test2). Use the Administrative Workstation to acces the Test1 and Test2 WLCs. Once configured you will need to verify that the mobility group peers are communicating properly.
Mobility Group Name: Mobility_Test
Mobility Group Members: Test1
IP Address: 192.168.1.99
MAC Address: b0:fa:eb:8c:2b:a0
Mobility Group Members: Test2
Ip Address 192.168.1.100
MAC Address: d0:c2:82:e3:aa:20
You have configured mobility group properly when the status of themobility group peers isUP.
TOPOLOGY
VIRTUAL TERMINAL
You have been tasked with setting up a mobility group (Mobility_Test) in a test lab. Thereare two WLCs that you will need to configure (Test1 and Test2). Use the Administrative Workstation to acces the Test1 and Test2 WLCs. Once configured you will need to verify that the mobility group peers are communicating properly.
Mobility Group Name: Mobility_Test
Mobility Group Members: Test1
IP Address: 192.168.1.99
MAC Address: b0:fa:eb:8c:2b:a0
Mobility Group Members: Test2
Ip Address 192.168.1.100
MAC Address: d0:c2:82:e3:aa:20
You have configured mobility group properly when the status of themobility group peers isUP.
TOPOLOGY
VIRTUAL TERMINAL
Correct Answer:
See explanation below
Explanation
Mobility Controllers belong to only one group, and can know several mobility groups On Test 1 WLC
1. Choose Controller> MobilityManagement > Mobility Peer
2. Click New
3. Enter the following details of Test 2:
a) Mobility Member IP
b) Mobility Member Public IP
c) Mobility Member Group Name
d) Multicast IP Address
4. Apply and Save
Similarly log in to Test 2 and enterdetails of Test1
Explanation
Mobility Controllers belong to only one group, and can know several mobility groups On Test 1 WLC
1. Choose Controller> MobilityManagement > Mobility Peer
2. Click New
3. Enter the following details of Test 2:
a) Mobility Member IP
b) Mobility Member Public IP
c) Mobility Member Group Name
d) Multicast IP Address
4. Apply and Save
Similarly log in to Test 2 and enterdetails of Test1
Question 3
An engineer is configuring visitor connect on their Cisco MSE. Which URL must they use for theirredirection URL?
Correct Answer: B
Question 4
An engineer wants to configure WebEx to adjust the precedence and override the QoS profile on the WLAN.
Which configuration is needed to complete this task?
Which configuration is needed to complete this task?
Correct Answer: C
Question 5
After a wireless deployment, users report that wireless voice clients are experiencing an unacceptable amount of delay while roaming during a call on theCisco Unified 7925 Series phones. The customer environment consists of multiple controllers, all running 7.4.121.0 code, operating in a centralized deployment. What configuration issue is most likely contributing to the problem?
Correct Answer: B
Question 6
Your network has these characteristics:
* CAC mode is set to load-based CAC
* The bandwidth usage is between 75 and 85 percent
* The reserved bandwidth for voice calls is exhausted
Which action occurs to TSPEC requests in this environment?
* CAC mode is set to load-based CAC
* The bandwidth usage is between 75 and 85 percent
* The reserved bandwidth for voice calls is exhausted
Which action occurs to TSPEC requests in this environment?
Correct Answer: B
Question 7
Which option is a calibration of a Cisco MSE deployment limited to whenthat deployment is using the linear point collection method?
Correct Answer: A
Question 8
An engineer would like to capture NetFlowdata onPI. Which resource is required to allow this?
Correct Answer: C
Question 9
An engineer must deploy FlexConnect APs to a site that typically has 300 ms latency to the WLC. Which typical operating mode must the engineer planon for normal operations?
Correct Answer: D
Question 10
A customer called with arequirement that internal clients must be on different subnets depending on the building they are in. All access points are operating in local mode and will not be modified, and this is a single controller solution. Which configuration changecreates the desired result?
Correct Answer: C
Question 11
You have just added a new MSE to Prime Infrastructure and want to synchronize the MSE with your 5508 WLC. which is located behind a firewall in a DMZ. You notice that NMSP messages are failing between the twodevices. What traffic needs to be allowed on the Firewall to ensure the MSE and WLC can communicate using NMSP?
Correct Answer: A
Question 12
A network engineer is debugging issues with the mDNS gateway. Which type of reply should be seen in the Wireshark capture when querying for a mDNS service in the Bonjour Cache?
Correct Answer: C
Question 13
The Cisco Unified Wireless Product supports WMM. On which Wi-Fi Alliance interoperability standard is this based?
Correct Answer: A
Question 14
A customer has implemented an N+1 cluster of WLCs without using an AP high availability configuration and is experiencing an unacceptable delay when clients areroaming. Which two configuration changes can improve roaming? (Choose two.)
Correct Answer: B,C