Dell PowerEdge Professional Exam (DCPPE-200) Free Practice Test

Question 1

An engineer receives two new I/O Aggregators (IOAs) in default mode. The engineer needs to make sure the uplink ports only pass tagged traffic in VLANs 100 and 200.
Which option allows the engineer to accomplish this task?

A. Remove all untagged VLANs from the uplink ports

B. Change the IOA mode to Programmable MUX mode

C. Tag only VLAN 100 and 200 on the uplink ports

D. Set the uplink ports to hybrid ports

Correct Answer: C

Question 2

Refer to the exhibit.
An engineer receives a pair of the modules shown to install in a pair of MXL switches.
Which cables does the engineer need for this module?

A. QSFP+ to QSFP+, 40GbE Passive Copper Direct Attach.

B. Cat6A Snagless Unshielded (UTP) Network Patch Cable

C. OM4 MTP Crossover Fiber Cable (optics required)

D. SFP+ to SFP+, 10GbE, Copper Twinax Direct Attach

Correct Answer: A

Question 3

An engineer is configuring VLT between two MXL switches. The engineer runs a show vlt brief command on one of the MXLs and receives the status shown in the exhibit. What should the engineer verify to fix the issue?

A. Both MXLs run the same firmware version

B. Both MXLs are powered on and fully booted into the OS

C. VLT cables are plugged in and have a link light

D. MXLs can ping each other on their management IPs

Correct Answer: A

Question 4

An engineer has connected a monitor, keyboard, and mouse to a VRTX chassis. The engineer is unable to see or control the first blade.
What must the engineer do to control the first blade with a connected monitor, keyboard, and mouse?

A. Map the KVM to the first blade in the Front Panel menu of the CMC.

B. Plug the monitor, keyboard, and mouse into the back of the chassis.

C. Enable the KVM for the chassis and navigate to the first blade.

D. Reseat the module that manages access to the monitor, keyboard and mouse.

Correct Answer: C

Question 5

An engineer needs to configure a single network port on a 10 GbE NIC for four virtual network interfaces.
What steps should the engineer perform to complete this task?

A. Configure the NIC port for NPAR. Configure global bandwidth allocations.

B. Configure the NIC port for Single Root I/O Virtualization. Configure Link Aggregation on the upstream switch port.

C. Configure the NIC port for Multi Root I/O Virtualization. Create four virtual ports in network device settings.

D. Configure the NIC port for Virtualization Technology. Create four virtual ports on the upstream switch.

Correct Answer: C

Question 6

An engineer needs to utilize the Server Configuration Profile (SCP) feature with the racadm command line tool to rapidly deploy a configuration to multiple servers. How should the engineer complete this task?

A. Export an SCP with the "--duplicate" flag, then import the SCP to the other server nodes.

B. Export an SCP, then import the SCP to the other server nodes using the "--duplicate" flag

C. Export an SCP with the "--clone" flag, then import the SCP to the other server nodes.

D. Export an SCP, then import the SCP to the other server nodes using the "--clone" flag.

Correct Answer: A

Question 7

An engineer needs to configure network port partitions for four networks that will be used on the server.
- Partition 1 - Management network
- Partition 2 - VM Live Migration network
- Partition 3 - Production VM network
- Partition 4 - Development VM network
The engineer needs to make sure the following conditions are met:
- Management and Live Migration networks do NOT exceed 1Gb
- Production VM network can use 10Gb but is guaranteed 5Gb during heavy use
- Development VM network has maximum bandwidth capability when NOT in use by the other networks Which network port partition bandwidth settings should the engineer set?

A. Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 009040Maximum Bandwidth1010100100

B. Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 1153Maximum Bandwidth111010

C. Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 1010 50 30 Maximum Bandwidth 1010 100 100

D. Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 0094Maximum Bandwidth1153

Correct Answer: D

Question 8

An engineer needs to enable automated proactive support from Dell for ProSupport entitled assets discovered in OpenManage Essentials.
What additional software should the engineer install?

A. Dell Phone Home for OpenManage Essentials

B. Dell ProSupport for Servers

C. Dell SupportAssist for OpenManage Essentials

D. Dell SupportAssist for Servers

Correct Answer: C

Question 9

An engineer is deploying a chassis with four IOAs and connecting it to the top of rack (ToR) switch. The deployment mandate requires that the switches can be managed individually. Also, future servers can be added to network with the minimal amount of configuration.
The following steps have been completed:
- Cabled port 9 between the two IOMs
- Cabled ports 10 and 11 on both IOMs to the ToR
- Configured a team on NIC ports 1 and 2 on the server
How should the IOMs be configured?

A. Virtual Link Trunking

B. Programmable MUX

C. Full Switch

D. Stack

Correct Answer: A

Question 10

An engineer is troubleshooting a VRTX with the following configuration:
- Dual Shared PERC Internal cards in a fault tolerant configuration
- Nodes installed in SLOTS 1 and 2
- Virtual adapters set to Multiple Assignment
- Two virtual drives set to Full Access on SLOTS 1 and 2
The OS of the node in SLOT 1 shows more than the two disks assigned to it.
What should the engineer do to fix this issue?

A. Power cycle the node in SLOT 1 to reset the connections

B. Set the virtual drives to No Access on SLOT 2

C. Configure MPIO services in the OS of SLOT 1

D. Set the virtual adapters to Single Assignment

Correct Answer: B

Welcome to TestSimulate

EMC Dell PowerEdge Professional (DCPPE-200) Free Practice Test