HP Aruba Data Center Network Specialist (HPE2-W09) Free Practice Test
Question 1
Does this correctly describe how the Virtual Switching Extension (VSX) fabric reacts to various component failure scenarios?
Solution: The keepalive goes down, ISL link remains up. Switch-1 and Switch-2 remains up. The Split-recovery mode is disabled. In this case the secondary switch shutdowns Svls.
Solution: The keepalive goes down, ISL link remains up. Switch-1 and Switch-2 remains up. The Split-recovery mode is disabled. In this case the secondary switch shutdowns Svls.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 2
Is this a best practice when positioning ArubaOS-CX switches in data center networks?
Solution: Deploy Aruba CX 83xx switches as data center spine switches.
Solution: Deploy Aruba CX 83xx switches as data center spine switches.
Correct Answer: B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 3
Refer to the exhibit. You want to enable devices in VRF B and VRF C to reach shared resources in VRF A. is this a valid strategy for meeting this goal?
Solution: Place ad three VRF$ in the same OSPF process on Switch-1.
Solution: Place ad three VRF$ in the same OSPF process on Switch-1.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 4
Is this how you should position switches in the ArubaOS-CX portfolio for data center networks?
Solution: Deploy Aruba 83xx switches as data center leaf switches.
Solution: Deploy Aruba 83xx switches as data center leaf switches.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 5
Does this correctly describe Network Analytics Engine (NAE) limitations on ArubaOS-CX switches?
Solution: Different switches have different limitations for the number of NAE scripts, monitors, and agents supported.
Solution: Different switches have different limitations for the number of NAE scripts, monitors, and agents supported.
Correct Answer: B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 6
Is this statement about ARP and ND Suppression true?
Solution: Both ARP-Suppression and ND-Suppression are disabled by default.
Solution: Both ARP-Suppression and ND-Suppression are disabled by default.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 7
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.
Is this what you should do?
Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 8
You are configuring Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. Is this a guideline for configuring timers?
Solution: The hold off timer causes ERPS switches to delay unblocking a failed link after the link is restored. This can be useful to prevent frequent topology changes.
Solution: The hold off timer causes ERPS switches to delay unblocking a failed link after the link is restored. This can be useful to prevent frequent topology changes.
Correct Answer: B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 9
Is this a requirement for implementing Priority Flow Control (PFC) on an ArubaOS-CX switch interface?
Solution: configuring trust of Cos on the interface
Solution: configuring trust of Cos on the interface
Correct Answer: B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 10
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: Create two configuration plans, one with the standard config and one with the device- specific settings.
Is this what you should do?
Solution: Create two configuration plans, one with the standard config and one with the device- specific settings.
Correct Answer: A
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).